Labconco 2246300
Basic 70 Laboratory Hood 6' model. 3/4hp motor and blower. With air foil, 2-piece adjustable baffle, tempered safety glass sash and pass-through port. Accepts up to 3 service fixtures, 2 duplex receptacles and cupsink with turret. 178Wx63.5Dx134.6Hcm. 115V, 60Hz. 0.23@100fpm (1120cfm). Exact Match: 30140-220

Labconco 112826002
Floor-Mounted Hood Floor-Mounted Hood 8 feet XL with Horizontal Sliding Sash, 43.7inch Depth, 2 Service Fixtures, 2 GFCI Duplexes, Dimensions: 96.0inch wx43.7inch dx95.0inch h, 115 volts, 60 Hz Exact Match: 10221-902

Labconco 1473400
Replacement Pump Exhaust Filter Replacement Pump Exhaust Filter, Weight: 1.0 lbs, Weight metric: 0.5 kg, Applicable Products: Rotary Vane Vacuum Pumps, Accessory for General Purpose Rotary Vane Vacuum Pumps, Disposable filter removes oil mist and odor from vacuum pump exhaust Exact Match: 10148-030

Labconco 180610000
Fume Hood Protector* Echo Filtered Fume Hood-Ecofoil Filter, 115V, No Glass, 0Fx 0 receptacle, 6ft, with Neutrodine filtration. Exact Match: 10746-870

Rack, Washer; Labconco; Spindle; Location: Lower; Provides direct injection cleaning through spindles; Weight: 20.0 lb.; Dimensions: 21.1W x 21.0D x 8.6 in. H; Accommodates glassware up to 18.7 in. H; 1/EA Exact Match 10359202 97002-962

Intelli-Sense Multi-Speed Coated Steel Blowers feature a direct drive ECM motor, which consumes one third less energy than belt drive motors, and a phenolic-coated impeller and housing. Unit comes with control box and 3 speed blower switch. Adjustable over broad range of airflows. Max of 350 CFM @ 0.08" SP to 1250 CFM @ 0.7" SP. 10" dia. inlet.

Labconco 7373436
Tubing Vacuum Tubing for vacuum pump connection to the Freeze Dry System, 3/4 inch inner diameter, 3feet length. Wire-reinforced PVC, Weight: 1.0 lbs, Weight metric: 0.5 kg Exact Match: 10148-062

Labconco 141610000
Hood Laboratory Hood 6ft Protector PVC Acid Digestion. 37.7in deep. Features heat-welded unplasticized PVC liner, built-in washdown system, integral work surface, drainage trough and 3-16in thick tempered safety glass vertical-rising sash with frame of powder-coated aluminum and PVC. 115V. Exact Match: 10118-538

Labconco 9905500
STORAGE CABINET ACID ADA 91.4 X 55.9 CM Exact Match: 76292-692

• Two pre-plumbed service fixtures with forged brass valves, lower right side with brass tubing for gas and lower left side with copper tubing for cold water. Components for converting either or both fixtures to air and vacuum are provided. Inlet tubing is not provided. • One pre-wired GFCI electrical duplex receptacle on lower right side. The Protector XStream Laboratory Hood takes containment, safety and energy savings to the extreme. This general chemical, high performance fume hood was independently tested and challenged well beyond the SEFA-1 standards. With a face velocity of 40 fpm and sash fully open, the Protector XStream was subjected to 50 fpm cross drafts, NIH protocol, and tracer gas measurements in the chest of the mannequin. In all scenarios, the Protector XStream allowed 0.00 ppm average level of tracer gas outside the fume hood. Although your safety officer will determine the actual face velocity setting for your laboratory, the ability of this hood to contain under these adverse conditions sets a new standard of safety. Safety is foremost, but energy savings is equally impressive. Although face velocity is a factor, it’s the volumetric rate (CFM) that determines the energy consumption. Operating a 6' Protector XStream at 60 fpm face velocity, with the sash in its fully open position, requires only 690 CFM. Regardless of your desired operating face velocity, the Protector XStream yields the lowest required CFM of any hood.