Blower, Exhaust; Labconco; Coated steel; 0.16hp; Belt driven; Gravity belt tightener, curved impellers, lubricated pillow, variable orientation; Use w/103-691-00, 103-691-01, 103-691-02, 103-691-03, 16-317; 115V 60Hz; 1/EA Exact Match 1609011

Blower, Exhaust; Labconco; Coated steel; 0.25hp; Belt driven; Gravity belt tightener, curved impellers, lubricated pillow, variable orientation; Use w/16-080, 16-317; 115V 60Hz; 1/EA Exact Match 1609012

Blower, Fiberglass; Labconco; 10.38 in. outer dia. inlet; 10.75 in. inner dia. outlet; 0.33hp motor; 1173-1456rpm range; Less than 1000 CFM; 115V 60Hz; 1/EA Exact Match 1609029 82006-780

Blower, Fiberglass; Labconco; 12.38 in. outer dia. inlet; 12.75 in. inner dia. outlet; 0.25hp motor; 569-753rpm range; Less than 1000 CFM; 115V 60Hz; 1/EA Exact Match 1609035

Blower, Fiberglass; Labconco; 12.38 in. outer dia. inlet; 12.75 in. inner dia. outlet; 0.5hp motor; 753-978rpm range; Between 640 and 1200CFM; 115V 60Hz; 1/EA Exact Match 1631111

Blower, Fiberglass; Labconco; 12.38 in. outer dia. inlet; 12.75 in. inner dia. outlet; 0.75hp motor; 920-1303rpm range; Between 1000 and 2000 CFM; 115/230V 60Hz; 1/EA Exact Match 1609039

• Two pre-plumbed service fixtures with forged brass valves, lower right side with brass tubing for gas and lower left side with copper tubing for cold water. Components for converting either or both fixtures to air and vacuum are provided. Inlet tubing is not provided. • One pre-wired GFCI electrical duplex receptacle on lower right side. The Protector XStream Laboratory Hood takes containment, safety and energy savings to the extreme. This general chemical, high performance fume hood was independently tested and challenged well beyond the SEFA-1 standards. With a face velocity of 40 fpm and sash fully open, the Protector XStream was subjected to 50 fpm cross drafts, NIH protocol, and tracer gas measurements in the chest of the mannequin. In all scenarios, the Protector XStream allowed 0.00 ppm average level of tracer gas outside the fume hood. Although your safety officer will determine the actual face velocity setting for your laboratory, the ability of this hood to contain under these adverse conditions sets a new standard of safety. Safety is foremost, but energy savings is equally impressive. Although face velocity is a factor, it’s the volumetric rate (CFM) that determines the energy consumption. Operating a 6' Protector XStream at 60 fpm face velocity, with the sash in its fully open position, requires only 690 CFM. Regardless of your desired operating face velocity, the Protector XStream yields the lowest required CFM of any hood.

Pump, Vacuum, Labconco; Rotary Van; Direct Drive, 117L/min., 3/8 hp Motor; 2.0 x 10superscript-7MPa Vacuum; Lifting Bracket, Use with FreeZone Freeze Dry Systems, Dimensions: 17L x 6.5W x 10.37 in. H; 115V 50/60Hz 7.8A; 1/EA Exact Match 109621 26671-484

Labconco 2247400
Basic 47 Laboratory Hood 4' model. Has air foil, 2-piece adjustable baffle, tempered safety glass sash, pass-through port with light and cover. Takes up to 3 service fixtures, 2 duplex receptacles, cupsink with turret. 120Wx63.5Dx122Hcm. 115V, 60Hz. Without motor and blower. 0.35@100fpm (720cfm). Exact Match: 30152-562

Standard Service Fixture Kit, Labconco; (GAS); Incl: remotely-controlled service fixture with 0.25in dia. brass valve and tubing, blue fixture knob and blue hose connector; For mounting on right side of Fume Hoods; Inlet tubing not included; 1/EA Exact Match 16331 15202-656